Vehicle Owner

Member ID: SlickWilly05

Location: Montevallo, AL

log in to make me an offer!

Vehicle Info

1993 Mazda MX-6

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed-1mph
  • HP-1
  • Weight-1lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Modifications

Performance Parts

Interior

  • Auto Meter Gauges 
  • B&M Shift Knob 

Exterior Styling

Ratings

    • Currently 3.0/5 Stars.

Login to rate

 

Parts On eBay

Last updated: Apr 10, 2007

Hits: 1,742

Will’s Mazda MX-6
“Mongoose (Cobra Eater)”

  • Currently 2.9666666666666 /5 Stars.
13 guestbook comments

This is the Mongoose
SlickWilly05's 1993 Mazda MX-6SlickWilly05's 1993 Mazda MX-6
SlickWilly05's 1993 Mazda MX-6SlickWilly05's 1993 Mazda MX-6
The Beginning:
SlickWilly05's 1993 Mazda MX-6 When i first bought the car about 3 years ago it had a blown engine, and i swapped the engine for the jdm KLZE engine, it only took me two months to blow the engine after that(threw a rod), and the motor after that i ran the rpm a little too high(10k) and blew the front head apart... So now, 3 motors and 3 years later, I am finally behind the wheel of an MX-6 that has gotten me addicted to boosted driving since the very first turbo'ed run down the street.

Mod list as of 4/7/07

-- MOTOR ---
Block:
- Cryo-treated
- Wiseco forged 8.5c/r pistons
- Wiseco moly rings
- Pauter forged billet 4340 rods
- Toga high volume oil pump
- Clevite 77 custom racing rod, thrust, & main bearings
- Balanced crankshaft
Heads:
- 3 angle valve job w/ custom ferrea oversized valves
- port matched to high perf. gaskets
- polished
Turbo Setup:
- Turbonetics T3/T4 60 trim comp .63 a/r Stg 3 Turbine
- Turbonetics Godzilla B.O.V.
- TurboSmart 38mm wastegate
- PWR "barrel" style Air-to-water chargecooler
- Stainless "hot" pipes
- Personally Fabricated intercooler pipes
- All "Earls" fittings and stainless braided line for oil supply/drain
Other motor stuff:
- gutted vris system from manifold
- removed AC system and cooling fan for ac
--- Other Performance ---
- 4" exhaust from downpipe to y-pipe & dual 2.5" pipes going to two Mugen twin-loop mufflers (nice and queit but WIDE OPEN FLOW)
- I have a megasquirt just need installer/programmer to make it less of a potential nightmare
- Clutchmaster Stg3 Clutch
- B&M short shifter (it wasn't short enough for me so I took off another 1.75 inches)
- Brembo Cross drilled rotors
- U-joint Axles (im currently underway on fabricating these)
--- Appearance & Safety ---
Body:
- House of Kolors - Lake Violet Pearl
- Buddy Club body kit
- Carbon fiber oem hood
- Body kit is fully molded
- Halo headlights
- IKON 17" Wheels
- Black 17" wheels w/ drag radials for the track
Interior:
- Entirely Stripped except for dash and door panels
"yay i have a homemade 2-seater now"
- Six point roll cage
- Six point harnesses
- Emergency fuel cutoff

Guestbook Ratings

Displaying entries 1-5 of 13

mazdamx601  

Posted by: mazdamx601

03/01/2008 09:59PM

hey can u give me sum info how much did u pay for your pistons and rods so let me no and i wus woundering if u could help me set up a turbo kit or where did u get yours id even pay u to help me out thanks adam

bradenAerhardt  

Posted by: bradenAerhardt

05/26/2007 04:41PM

Hey man I have a question for you. Did you need to cut the crossmember inorder to fit the down pipe from the turbo to the exhaust? If you didnt how did you get the piping to fit?

94mazmx6  

Posted by: 94mazmx6

04/11/2007 07:59AM

thanks 4 the comment yea i knw i cant wait to be boosted ive def been savin up 4 it, i have alot of friends who are boosted so i thought i needed to do the same to keep up with them lol, but ill def be askin u questions when i get started with it

94mazmx6  

Posted by: 94mazmx6

04/08/2007 01:49PM

great 6 man def lookin really clean, i like the turbo setup hows it treatin you im gettin mine from probeaddiction next month, check mine out if you get time

deric27  

Posted by: deric27

04/07/2007 07:02PM

niiice mx3. give us some more pics of the finished product. check out my 240. it ain't much yet, but its a work in progress.

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: SlickWilly05

Location: Montevallo, AL