Vehicle Owner

Member ID: daveofsac

Location: Sacramento, CA

Vehicle Info

2001 Mazda Miata

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed-1mph
  • HP-1
  • Weight-1lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Ratings

    • Currently 3.0/5 Stars.

Login to rate

 

Parts On eBay

Last updated: Jul 25, 2005

Hits: 5,716

r’s Mazda Miata

  • Currently 2.96 /5 Stars.
9 guestbook comments

========================================
Hot Dog "Double Diagonal" Roll Bar
========================================

The following is a write up on a rollbar install. This is a REAL rollbar and not a style-bar. While style-bar have its place, for a ragtop... a real rollbar is better at protecting your head.

daveofsac's 2001 Mazda Miata

I ordered my rollbar directly from Bethania Garage Inc. After looking at all the styles, I settled for the M2 Hard-Core with Double Diagonal. Here�s the package as it was delivered from BGI. The packaging was real nice and UPS actually kept it in one piece.

daveofsac's 2001 Mazda Miata

First thing first, double check your package and make sure you have all the bolts and nuts, and washers. The instruction that came with the bar was good, but online help from Miata.net will help a little. Before starting, I highly recommend removing the two seats� it will make your install life easier.

When you are ready to start, the first thing is getting the carpeting off the rear deck. You need to remove the plastic snap-caps holding the carpeting to the soft-top inner lip. After the carpeting if off the rear deck, start removing the plastic trim and everything else that needs to get out of the way. In no practical order� metal deck lid, seatbelt bolt & seatbelt housing, plastic trim, windblock trim, door trimming, and side striker plate.

daveofsac's 2001 Mazda Miata

When you are done, you should have something like what�s pictured above. I also found that unplugging the wiring harness on the right side to be helpful in fitting the rollbar.

daveofsac's 2001 Mazda Miata

After that, test the rollbar for fitting issue and see if everything lines up. If the rollbar fits, everything should line up and sitting correctly like the above picture.

daveofsac's 2001 Mazda Miata

Here you see the wiring harness unplugged for fitting.

daveofsac's 2001 Mazda Miata

Some more picture of the fitting. If fitting looks good, bolt the seatbelt housing & bracket back in place.

daveofsac's 2001 Mazda Miata

The holes should line up correct and allow the rollbar to be bolted in with the seatbelt bracket. Make sure your seatbelt housing is lined up correctly before bolting the rollbar into place because you won�t be dealing with the housing after this.

----------

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

----------

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

----------

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

----------

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

daveofsac's 2001 Mazda Miata

Guestbook

Displaying entries 1-5 of 9

allamerican23  

Posted by: allamerican23

07/27/2005 10:14AM

I owe you a tip. get the yellow LED (has 4 leds)wedge bulbs for your sidemarkers from autozone. They are really crisp and clean looking. I have them on my vette and they were better than I had hoped. I owed you this cause I needed your annodizing info :) didnt look through the rest of your pages but cool site!

punk_dexter  

Posted by: punk_dexter

03/25/2005 07:31PM

Hey man! I just gotta say, your site is probably one of the best do it yourself pages I have seen. I had been thinking about making a air-box around my intake, but wasn't sure how to do it, but your page showed me a lot, and now I am all geared up to take on the task! Thanks so much! Your Miata is looking good! Come check out my Civic sometime and tell me what you think. Also, there is a link at the top of all my pages for a message board that I am a member of, It isn't very big yet, but I really think you'd fit right in! Thanks again! L8R! Punk Dexter

86MR2lover  

Posted by: 86MR2lover

03/07/2004 09:23AM

hey i like it! dont the miatas have a 1.6? cuz i have an 86 MR2 with the same engine and i just wanted to know if the parts for the miata fits my car check mine out lata, peace

neon77  

Posted by: neon77

03/07/2004 08:08AM

nice car, looks real good. keep me updated on future mods and pics. stop and checkout my ride sometime, peace!

hondasmoka  

Posted by: hondasmoka

03/07/2004 07:57AM

nice car i love what you have done with it, keep up the good work!o yea i almost forgot check out my page please.

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: daveofsac

Location: Sacramento, CA