Nasco Seat Belts.Addvertisment from 1964 "All New Design" The Seat Belt.Below is the box they where sold in.Top is the sticker which was place on the buckel.
This is a Carby Jet Tool for the FX-EJ Holden Stronberg Carby. The tool is Coxhead brand, an is marked "COXHEAD". The tool is used to remove the jet plugs from under the carby, and then the jets WITH THE CARBY STILL MOUNTED IN THE CAR! This tool has a screwdriver blade on end, and a key for the jet to the other. This tool can be used to remove and clear a blocked jet from a carby in a few mins, on the side of the road.
Nasco Universal Rear Reflectors .Part # M30972.
1948 HOLDEN FACTS BOOK ,everything to know about the NEW 48-215 HOLDEN IN AUSTRALIA. Approx 4 1/4 inches (110mm) by 5 3/4 inches (145mm) and is 86 pages with a fibre cover.
'Your Job at GMH' 63 page booklet printed in 1954. As the title implies, this booklet is all about working at GMH - your job, your pay, social centre and activities, plant regulations and so on. The other three smaller booklets where in the back pocket of the book , being - a 15 page 'Suggestions Pay Dividends' booklet, an 8 page 'Increase your Pay' booklet and a 15 page 'Sickness and Accident Fund' booklet.All four booklets make very interesting reading and give an incredible insight into the working conditions of those employed to make our first Holdens.eg Did you know employees were entitled to one cup of tea per day - and they had to pay for it and drink it whilst still working and could not smoke within 20 feet of spray booths ?
1954 General Motors Calander. Addvertising the FJ Holden.
Speco Headers for the Holden Grey Motor.
Over the years I have never seen a GREY MOTOR one piece headers which KLEINIG MOTORS SYDNEY produced (Power Equipment)!!!!!HAVE YOU!!!!! Was told from a fellow that he saw a old magazine article that stated that less then one dozen of these one piece headers were ever produced ( Not shore if true) also in the same article claimed that it could double the horsepower of your Holden Grey Motor with a set of twin carbie.
Speco Fuel Splitter. This is a device used when running twin carbies (Like above). It splits your single fuel line into 2 outlets for connection to each carby.
Alloy Speco Rocker Cover.Purpose was to lower the noise of the tapet rattel in the grey motor and allso to fancy up the engine bay.
Nasco seat cover instructions.Nasco seat covers where mainly clear plastic covers.For you could still then see the colour of the seat trim.
FX - FJ Holden Brake Drum "Hub Removal Tool".Known to be difficult without it.
FJ Holden Nasco Venetian Blind.This is fitted to the back window but from the inside.Commin colour was white.
AWA (Amalgamated Wireless Australasia) is another 6 volt valve radio that was fitted to the FJ Holden.Model 3Z, it had a rather plain looking facia.
Nasco Dash Rack.This was fitted to the dash where you desired with 2 small suction caps to hold it.
The FJ Holden tool kit was keep to a minimum.1 orange handled 4 inch flat head screw driver,1 combination pliers,1 tube spanner with a suitably sized opening on one end for the spark plugs doubled up as a wheel nut wrench on the other end,1 short stout bar whish was used to slipped through the tube spanner to supply leverage.It also had a forged end,which facilitated the romoval of the hub cap.The tools where kept in a envolop tool bag made out of vinyl 300mm x 137 mm.
NASCO Sealer Tin being a half pint .Part # 3835215 .
Width 7 1/2 cms x Height 8 1/2 cms .
This Jack was bought out in the FJ Holdens. It is 4 1/2 inchs high. On the left is the fold up jack handle that went with it.
This is a Nasco Bug Reflector which prevents bugs from hitting the front windscreen .It's fitted under the bonnet mascot.It come in different colours, white, blue, red, yellow and green.
Nasco inner door pull handles.These ones were made only for the FX and FJ Holden.If you look closly at the handles ,they have ripples on them which is replica to the door window winder handles, inner door opening handle and outer door handles on the FX/FJ Holdens.
Rare FJ Holden fuel cap with a reflector in the middle.
Tappet wrench tool.Was produced for the Holden grey motor.For adjusting the tappets.
Rare grey motor "KLEINIG SYDNEY TWIN BREATHER ALLOY ROCKER COVER".This allows the engine to breath better.
FX-FJ Nasco Radiator Core Part # M.7400960.
Very rare set off 48-215 / FJ Holden front Nasco shocker spacers and bolts .These were used to raise the shocker height. Part No is 7405728
Nasco interior roller blinds for the FX-FJ Holden doors windows. A unique accessory of the fifties, blocking the sun out and giving privacy. They measure:Drop is aprox 300ml width 350ml.
Holden Grey Motor Marine Manifold designed by TAWCO PRODUCTS. The GMH grey motors were offen placed in boats as they were a powerfull motor in them days.This manifold aloud you to have 1, 2, or 3 carbies at a time giving more power.
FJ - FX Holden Pivot Pin Kit in Original Packaging.Kit # 7406726.
FX-FJ 15 inch to 13 inch wheel converion plate.
This is a very rare FX-FJ Holden accessory, called Fender Darts.
Early 50's Nasco number plate frames.These were designed to fit the old Q number plates which were longer,an also for the standed size (like todays).
Above is pictures of the front and back of 15inch Nasco Trim Rings being for the FX-FJ Holden Wheels.
Nasco Four Point Socket Wrench. Part Number Z4270.
7/8 A/F , 13/16 A/f , 3/4 A/F , 11/16 A/F.
