Vehicle Owner

Member ID: CLARKIE99

Location: Adelaide, AU

Vehicle Info

1990 Mazda 626

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed-1mph
  • HP-1
  • Weight-1lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Ratings

    • Currently 3.0/5 Stars.

Login to rate

 

Last updated: Jan 22, 2009

Hits: 146

Dan’s Mazda 626

  • Currently 2.96 /5 Stars.
6 guestbook comments

CLARKIE99's 1990 Mazda 626heres a photo of my car. looked good at the time

CLARKIE99's 1990 Mazda 626here ive installed 6" in the door since the stock are too small and sit in the lower dash. (better sound now)

CLARKIE99's 1990 Mazda 626heres my painted dash with my deck, i now have a new deck, the 2008 pioneer model that lights up green not red(that one is the 2007 model)

CLARKIE99's 1990 Mazda 626heres my neons i installed a while back, i also mounted 2 8" in the back but now to a trade with my mate i dont have them anymore, as they were to bright and hardly used them lol

CLARKIE99's 1990 Mazda 626 inside my car pic explains its self, blue dash, gear boot//knob and metal pedals, steel need to get a steering wheel and boss kit, but low on funds

CLARKIE99's 1990 Mazda 626my 800 watt pionner sub, and my 300 watt pionner mono block, still have sub but amp has been replaced with a 400 watt clarion 2 channel ALOT BETTER!

CLARKIE99's 1990 Mazda 626 front view stock all ova except my fog//driving lights i put on myself

CLARKIE99's 1990 Mazda 626front nothing much to add

CLARKIE99's 1990 Mazda 626back. installed a cannon muffler. came off a forester. nice tone too it but running too rich atm.

I know my car isnt the world best but hey its a 1000 buck run around, im young and put a few bucks into it to make it personal. If i plan to keep it, its going to get sprayed black, then dropped 50mm, some nice mags maybe 17's and then re tinted. But ill see how the $$$ is.

Guestbook

Displaying entries 1-5 of 6

Blusube  

Posted by: Blusube

03/22/2009 03:01PM

Save up bit by bit, mod by mod, do the cheapest mod first. Drop by and check out my TX5.

Davididid  

Posted by: Davididid

01/22/2009 11:33PM

haha hey buddy hows it hanging! add us on the old msn casmandt@gmail.com you should come out to my car clubs cruise tomorrow ;) www.myspace.com/bluestreakcc nice to see someone reppin the 626's LOL take it easy

Davididid  

Posted by: Davididid

01/22/2009 11:32PM

haha hey buddy hows it hanging! add us on the old msn casmandt@gmail.com

narcarsiss  

Posted by: narcarsiss

01/22/2009 08:45PM

Mate it is not about how the dollar is... It's about how much dollar you want to spend! Personally i have $9000 to spend on my hole car but the engine alone is going to cost me about $16000 to fully rebuild... Not including full white retrim interior not BLOODY spray paint! Then There Is Body Work Custom Kit Custome paint New Rims Enkei FN18's In Perticular Why Spend All This On A Mazda CAUSE I CAN!! Wish You Luck On Your Project Cheers DAmo

KastropheX  

Posted by: KastropheX

01/22/2009 09:31AM

Hey man what I did was cut some designs out of a newspaper and made a reversed replica of the design I liked. Then I took masking tape and covered the holes I made for the tape and cut those out of the newspaper template I created.

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: CLARKIE99

Location: Adelaide, AU