Vehicle Owner

Member ID: Low_Rine

Location: Kamloops, BC

Vehicle Info

1989 Nissan Skyline

Bought: Dec, 2007

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed113mph
  • HP280
  • Weight2770lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Modifications

Performance Parts

Interior

Exterior Styling

Car Audio & Video

Ratings

    • Currently 3.8/5 Stars.
    • Currently 3.7/5 Stars.
    • Currently 3.7/5 Stars.
    • Currently 3.6/5 Stars.
    • Currently 3.7/5 Stars.

Login to rate

 

Last updated: May 10, 2009

Hits: 4,256

Jay’s Nissan Skyline
“Project34”

  • Currently 3.8 /5 Stars.
60 guestbook comments

ENGINE:
RB25DET swap
RB-series 2.5L DOHC
Turbo/Intercooled

 The RB25DET engine wasn't found until later on in the R33 Skyline which was introduced  
 in August of 1993. Although the R33's were slightly heavier, this engine swap into the  
 older HCR32 should be very interesting!
 

  • Bore & Stroke: 86 X 71.7
  • Capacity: 2498cc
  • Power: 250HP/235Tq (319Nm) OEM
  • Compression 9:1

TRANSMISSION:

Gear ratios:

1st - 3.321
2nd - 1.902
3rd - 1.308
4th - 1.000
5th - 0.759
Reverse - 3.636
Final - 4.300

DIFFERENTIAL:

VLSD (Viscous limited slip differential)


Low_Rine's 1989 Nissan Skyline

Low_Rine's 1989 Nissan Skyline
Custom air deflector

Low_Rine's 1989 Nissan Skyline
Custom BOV plate on stock intake pipe

Low_Rine's 1989 Nissan Skyline
Custom SRI with heatshield

Low_Rine's 1989 Nissan Skyline
RB25DET engine arrival from Japan

Low_Rine's 1989 Nissan Skyline
Polished intake manifold/ FMIC install



Mods:

Trust/Greddy FMIC
Custom grainger valve (Boosted @ 10PSI)
Blitz BOV on custom mounting plate
K&N cone airfilter (custom)
Custom heatshield
Custom air deflector
Silicone vacuum lines by Vibrant
Full 3" Mandrel bent exhaust system
3" testpipe
Magnaflow race series muffler

Guestbook

Displaying entries 1-5 of 60

Low_Rine  

Posted by: Low_Rine

06/16/2009 01:15PM

its from/for a R33, youll need to customize it to fit, meaning a bit of trimming off the bumper at each corner. Then a custom bracket JBWELD'd to the bottom/center of the grille. It will bolt up directly in 3 spot locations.

fattony15  

Posted by: fattony15

06/15/2009 08:04AM

5* for sure. I was wondering where you got the open mouth style grill. I am currently working on a project myself and would love to get one.

ryan_heather  

Posted by: ryan_heather

05/10/2009 09:22PM

nice ride, looks real clean 5stars. come check out my prelude sometime

Low_Rine  

Posted by: Low_Rine

05/09/2009 11:15PM

much appreciated! finally got the custom 3" downpipe installed a few weeks ago now, the car opens up like a mofo now. But now that the Emanage is almost ready to go, which would bump the HP up to around the 340HP mark would be pretty sweet. Pulled the circuit board out of it and set those up and have the harness leading to the ECU ready to be wired in and tuned which i got a quote for around 240.00 CDN.

Vietboi781  

Posted by: Vietboi781

05/08/2009 06:59PM

dats one badass GTR. Haven't seen too many in that color. Nice ride.5x

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: Low_Rine

Location: Kamloops, BC