Vehicle Owner

Member ID: Mitchell_1998_Gt

Location: Charlotte, NC

Vehicle Info

1998 Ford Mustang

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed-1mph
  • HP-1
  • Weight-1lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Modifications

Performance Parts

Interior

Exterior Styling

Ratings

    • Currently 3.0/5 Stars.
    • Currently 3.0/5 Stars.
    • Currently 3.0/5 Stars.
    • Currently 3.0/5 Stars.
    • Currently 3.0/5 Stars.
    • Currently 3.0/5 Stars.

Login to rate

 

Last updated: Jan 16, 2008

Hits: 695

Mitchell’s Ford Mustang

  • Currently 2.96 /5 Stars.
9 guestbook comments

Mitchell_1998_Gt's 1998 Ford Mustang

Mitchell_1998_Gt's 1998 Ford Mustang

Mitchell_1998_Gt's 1998 Ford Mustang

Mitchell_1998_Gt's 1998 Ford Mustang

Ford 1995 Cobra R's with Kumho Supras 255/40 wr's
Steeda Race Wing
HO Fibertrends 1 1/2" Cobra R hood
Ford Cobra Body Kit
Shaved Emblems
Shaved Antenna
Tinted Windows
Eibach Prokit
KYB GR2's "To Be Installed"
Poly Bushing Kit "To Be Installed"
Kenny Brown Subframes
Offset steering rack bushings
K&N filter
Mac Cat Back
Mac O/R Prochamber
PI intake
Corbeau Seats
March Under drives "To Be Installed"

RWHP: 185
RWTQ: 231
A/F Ratio after 4k went to 11.2 EXTREMELY RICH! NEEDS TUNE!

In the works for the Upgrades.

Since i'm looking at getting a D.D. beater car i'm going to be parking the stang to do some hot roding to it >:D

Plans

5.4L Ligntning Motor , 330 CI SOHC 16V
Stage 3 Ported Heads
Custom Supercharger Cams with LOTS of lift
Forged Rods to go along with the factory forged pistons and crank
Balancing work
Ported Supercharger
14/18 PSI pulley for supercharger
Custom Tune
Stall Converter
Built 4r70w or 4r75w
3.55 or 3.73 gears
Trans cooler
Shift Kit
B&M Hammer shifter
31 spine diff. and axles
Alum. drive shaft and safty loop
Tubular K member and A arms
Front Coil over kit
15X10 or 11's and some really sticky rubber on the back

Guestbook

Displaying entries 1-5 of 9

mattk1  

Posted by: mattk1

11/24/2007 08:41AM

Thanks for the comments. I liked the sound of the FRPP exhaust, but it wansn't loud enough for me and it also pinched down to 2.25" inlet/outlet at the mufflers with the rest of the catback is 2.5", so wanted to get rid of that restriction. For future improvements, definately want a tune with Xcal2 and top of the engine with either PI or SVO heads. low-mid 13s car is the gameplan.

mattk1  

Posted by: mattk1

11/10/2007 07:12PM

Looks good from what I can tell. upload bigger pics and keep up the good work!

DracoSTi  

Posted by: DracoSTi

09/14/2007 07:54AM

That is a very nice car, bring it out to Draco Performance so that I can take a look at it. We look forward to doing the DOHC swap and doing the tuning on it. Check out my daily driven shop/track car and let me know what you think. We'll see you soon.

tboyz98ondubs  

Posted by: tboyz98ondubs

03/13/2007 06:57AM

Are you selling the hood

tboyz98ondubs  

Posted by: tboyz98ondubs

03/09/2007 11:57AM

Nice stang

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: Mitchell_1998_Gt

Location: Charlotte, NC