Vehicle Owner

Member ID: yosteff

Location: st-hubert, QC

Vehicle Info

1996 Chevrolet Camaro

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed-1mph
  • HP350
  • Weight-1lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Modifications

Performance Parts

Interior

  • Nu Image Gauges 
  • APC Pedals 
  • Custom Shift Knob 
  • Bride Seats 

Exterior Styling

Ratings

    • Currently 3.4/5 Stars.
    • Currently 3.1/5 Stars.
    • Currently 3.2/5 Stars.
    • Currently 3.0/5 Stars.

Login to rate

 

Last updated: Sep 29, 2009

Hits: 5,804

Stephane’s Chevrolet Camaro
“Track Camaro Project (TCP)”

  • Currently 3.38 /5 Stars.
18 guestbook comments

ENGINE

I have swaped a LS1 from a 1998 Firebird Formula and all the wiring and accesories that was with it.

yosteff's 1996 Chevrolet Camaroyosteff's 1996 Chevrolet Camaro

yosteff's 1996 Chevrolet Camaroyosteff's 1996 Chevrolet Camaro

yosteff's 1996 Chevrolet Camaroyosteff's 1996 Chevrolet Camaro

yosteff's 1996 Chevrolet Camaroyosteff's 1996 Chevrolet Camaro

I put a cold air intake that go all the way in the fender.  Blue taylor wires,  Mac performances 3 inch Cat back, but i find that it is not loud enough. I am thinking about instaling some Pacesetter long tube  Headers, off-road Y pipe and catco converter.  

DRIVETRAIN

 I replaced the weak, almost busted 2 pieces drive shaft,when i was using the V6 with a 1 piece steel drive shaft. And from the firebird i used the aluminum drive shaft that is sitting behind the Manual 6 speeds transmission equiped with a SPEC stage 2 clutch kit.  I have performed the drill mod on the master cylinger. but after the instalation, i founded that the rudd was not long enough. I modded it a bit and now have it fully adjustable! I replaced the worn out factory transmission rubber mount by a full poly mount. Plus, the factory LS1 trans cross member dont fit under the 1996 Camaro and not even the V6 one. So was able to get a LT1 6 speed cross member to make everything fit nice.

yosteff's 1996 Chevrolet Camaro

 I replaced the stock open diff by a Auburn Gear posi unit. Pretty tough job for the first timer!!! The Firebird Diff was broken in the crash...i will try to repared it when i have some time. 

FUEL

I got to replaced my fuel pump. So insted of paying 500$ at the dealer for the OEM pump i decided to buy a Walbro race fuel pump. This sucker can move 255 galon/hrs. Sure better than the regular and the price was way better too..120$ on Ebay!!!  

yosteff's 1996 Chevrolet Camaro


Since the mechanic guy was asking me 5 to 6 hrs of work time at 65$/hrs!!! i deceided to do it myself and go by the access panel..you can see a good guide here for the fuel pump and other mods.

http://home.comcast.net/~grayman99/guide.htm

It was not that hard and it dint take me long to cut it.

yosteff's 1996 Chevrolet Camaro     yosteff's 1996 Chevrolet Camaro

yosteff's 1996 Chevrolet Camaro   yosteff's 1996 Chevrolet Camaro

 The only modification, was to splice 2 wires and cut a rubber insulator a little bit to fit ok on the new fuel pump, that was the same size.

 

But when i swapped the LS1, the fuel system and hoses, was different so i swapped them from the Bird in the Camaro.

 

 

 

 

 

 

Page 1: Suspension
Page 2: Interior and Exterior 
Page 3: Engine and drive train
Page 4: Wheels/Tires and Brakes

Page 5: Dreams camaro, Racing pics and videos

 

 

 

 

 

Guestbook

Displaying entries 1-5 of 18

Jesus0509  

Posted by: Jesus0509

08/22/2009 06:47PM

that is a nice project you did... good job...

Devylyst  

Posted by: Devylyst

03/14/2009 05:52PM

None are mine, it's just a tribute page to Dick Harrell and GMMG performance.

shourdsy_06  

Posted by: shourdsy_06

03/11/2009 02:15PM

Thanks for the comments. Very nice additions. Like the shifter. *****

camarosource  

Posted by: camarosource

02/12/2009 04:00AM

Fellow Camaro Owner - ** Camarosource.ca NOW Accepting pics for Camaro 2010 Calendars ** http://www.camarosource.ca/main_new_site.php?url=2010_calendars/index.htm I also posted a msg on the forum with more info http://www.camarosource.ca/forums/viewtopic.php?t=17658

SipesRacing  

Posted by: SipesRacing

02/04/2009 12:37PM

Thanks for the comments..... Hope to see more mods for yours in the future! keep me updated!

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: yosteff

Location: st-hubert, QC