Vehicle Owner

Member ID: outlawzxblizz99

Location: McGuire AFB, NJ

Vehicle Info

1991 Eagle Talon

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed-1mph
  • HP-1
  • Weight-1lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Ratings

    • Currently 3.2/5 Stars.
    • Currently 3.2/5 Stars.
    • Currently 3.2/5 Stars.

Login to rate

 

Last updated: May 09, 2008

Hits: 1,390

RP’s Eagle Talon
“The Street Sleeper : R.I.P.”

  • Currently 3.225 /5 Stars.
3 guestbook comments

outlawzxblizz99's 1991 Eagle Talon

Since the sidebar is sooooo limited....here's a list of my mods....

*Mods In The Whip*

Engine-
-HKS 264/272 cams
-Unorthodox underdrive pulley
-Buschur front mount intercooler
-Buschur full 3inch exhaust
-Buschur 3inch downpipe
-Buschur 3inch test pipe
-2g MAS
-Injen Intake
-255 walbaro fuel pump
-Denso 550cc injectors
-Manual boost controller
-Ported 2g exhaust manifold
-3" tubular 02 housing w/ external dump
-Evo 3 turbo w/stainless steel oil feed line from oil filter
-Blitz BOV recirculated
-8.5mm magnecore wires
-short shifter
-Aeromotive FPR
-egr blockoff w/ emission removal
-ARP headstuds
-Cometic MLS headgasket
-NGK BPR8ES Spark Plugs

Suspension/Handling/Brakes-
-94 big brake upgrade
-Stainless steel brake lines all around
-Powerslot rotors all around
-Metal master brake pads all around
-Kyb agx (4adj in front 8way adj in back)
-Eibach prokit springs 3/4 inch drop
-Front and back strut tower braces

Electronic-
-Super afc 1
-VDO exhaust temp gauge and boost gauge, Autometer air/fuel gauge
-Greddy turbo timer
-MMCD datalogger on Handspring Treo 300

---------------------------------------------------------------

Guestbook

Displaying entries 1-3 of 3

4g63demon  

Posted by: 4g63demon

02/11/2006 05:08PM

Hey nice talon. I like the mod list. I noticed that your front bumper is sagging a little bit from the intercooler. I had the same problem but i solved it by using a heat gun. I then held it together with some wire made clamps until it cooled. It took the original shape again. Make sure the bumper isnt touching the core. Cause you might have to shave a little before heating it.
check out my page lemme know what you think

ts1awd  

Posted by: ts1awd

11/28/2005 07:15PM

You have a great start to a really fast DSM. You have all of the supporting mods already in place for a really nice turbo. I think upgrading to a EVO III 16G would still be a downgrade. Being a FWD, I think you would benefit the most from a unported unclipped TD06 20G in a 7cm housing. Get back with me if you want some prices on a great vendor in my area. It will spool fully around 3800 wich will give your tire roasting FWD time to get going, and it will pull like crazy on the top end, with still being a very streetable turbo. Second of all, ditch the air flow meter and you will see huge gains and tuning ability with a VPC, DSMLink or EMS. Thats my 2 cents, you asked for it! Thanks for coming to my site. Great car!

eagletalontsi123  

Posted by: eagletalontsi123

11/26/2005 04:50PM

looks good dude, check out my TSi

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: outlawzxblizz99

Location: McGuire AFB, NJ