Vehicle Owner

Member ID: 626DXGT

Location: Plano, TX

Vehicle Info

1991 Mazda 626

Bragging Rights

  • 1/4 Mile0 sec @ -1 mph
  • 0-600sec
  • Top Speed-1mph
  • HP-1
  • Weight-1lbs

Major Upgrades

  • turbo
  • nitrous
  • bore increase
  • port and polish
  • supercharger
  • extrude honed
  • stroke increase
  • engine swap

Ratings

    • Currently 3.3/5 Stars.
    • Currently 3.2/5 Stars.
    • Currently 3.1/5 Stars.
    • Currently 3.2/5 Stars.
    • Currently 2.9/5 Stars.

Login to rate

 

Last updated: Sep 25, 2009

Hits: 18,538

Mike’s Mazda 626
“Sleeper626”

  • Currently 3.29 /5 Stars.
38 guestbook comments

i finally wanted to swap the turbo trans into my car. i had to get a few pieces from the junkyards to complete the swap. i found that the knuckles in the front had to be replaced. the hubs were bigger and needed to be replaced to hold the bigger axles. i swapped the front knuckle assembiles and trans. i had to get a trans from the yard also cause the PGT one was damaged inside and needed new parts that i couldnt find. i got the other trans for 35$ and it had a new clutch assembly, i toom it and replaced the slave cylinder. the clutch line needed to also be rteplaced.
626DXGT's 1991 Mazda 626

626DXGT's 1991 Mazda 626


626DXGT's 1991 Mazda 626

626DXGT's 1991 Mazda 626


626DXGT's 1991 Mazda 626
626DXGT's 1991 Mazda 626
i would of had more pics but my camera had died on me so i couldnt take the pics i wanted to, o well.
i have joined with a few clubs online but i have a local group that meet with. make sure u check them out if u are in the DFW area. www.dfwmazdas.com

626DXGT's 1991 Mazda 626

626DXGT's 1991 Mazda 626


626DXGT's 1991 Mazda 626

Guestbook

Displaying entries 1-5 of 38

Spawn1981  

Posted by: Spawn1981

09/17/2009 02:44AM

Hi there! really nice car and cool project! i'm looking for two parts for my GD, the digital speedo and the moving vent in the middle console! is it possible to find something in the USA?

ImportRacer93  

Posted by: ImportRacer93

08/11/2009 08:39AM

Sic GDs man. Is taht a AWR strut bar? Im currently working on swapping the motor tranny and rear end onto my 626. Right now the mods it has are Intrax suspension CAI, and custom exhaust with a civic short throw. In the next few days i hope to have my fuel cell in soon. Maybe on day ill get my mazda lookin as good as yours.

Blusube  

Posted by: Blusube

07/10/2009 05:26PM

finally got my low springs in my car almost done

_DisTurBed1_  

Posted by: _DisTurBed1_

04/10/2009 11:24PM

wow.. im not even a big fan of the 626's.. i don't really know why, but this is an amazing car... you've done alot of work to really make this car look good. nice work! deffinatly 5*s if ya get time you should let me know what you think about my cars.

StationW  

Posted by: StationW

03/27/2009 02:05PM

I ask it because I read on www.performanceprobe.com (same engine)that the 2.2 12V cylinder head have a "bottleneck" effect about 210 hp, because the valves are too small, and there's not enough space for bigger ones.

Show Older Comments

Post a comment

Bookmark this Ride

Vehicle Owner

Member ID: 626DXGT

Location: Plano, TX