Clean 318! mods: K&N FIPK, Magnecore 8.5mm wires, brass cap and rotor, Bosch Platinum plugs, custom bent Flowmaster exhaust with a high flow cat going in... Show more soon. I'm in the middle of dressing the hoses in this shot.
New battery, still waiting for the Stinger negative terminal then I'll add a 4 gauge chassis ground.
Stinger Power2 Battery info.
The Power2 is the next generation of high performance batteries from Stinger Electronics. The Power2 utilizes dry cell technology and an ultra-thin lead plate design that results in a powerful yet compact battery. The advanced design offers an internal resistance of an amazingly low 3.1 milliohms (this represents a 31% improvement over the last design). An absorbed glass mat (AGM) separator utilizes micro fibers to suspend the electrolyte within the battery. There is no fluid to spill or leak and these dry cell batteries are completely sealed and require zero maintenance. Copper alloy terminals ensure proper current transfer and corrosion free operation. The versatility of the Power2 Master allows it to be used as a secondary deep cycle battery or primary engine start battery. Maximum terminal discharge current is 1,000 amps. Dimensions are 6 1/2" W x 6 7/8" L x 5" H (add 5/8" to height for battery post). With its new metal case, the Power2 is designed to last up to 12 years.
Rockford Fosgate Fanatic-Q 5.5" components in the doors. I like the look of the crossovers so they were installed out in the open. Lots of Cascade VBlok paste on the panels and a can of spray inside.
Rockford Fosgate Fanatic-Q 6.5" components in the rear panels. The tweeters are up high on the window trim, again the crossovers are out in the open. All the interior was removed behind the front seats and coated with VBlok paste and a few sheets of Dynamat behind the 6.5s.
Proprietary molded ABS baskets on midrange
3-layer glass fiber composite cone
1.25" multilayered copper voice coil
0.75" (20mm) aluminum tweeter dome with silk surround
24dB/octave symmetrical lowpass/highpass
Optical tweeter protection
Nominal Impedence 4 ohms
Frequency Response 45Hz-20kHz
RMS / Peak Power 100 watts/200 watts
I was in a rush at this point to get the installation done before taking the kids to Disneyland so I did not get any good pictures before finishing. I had to really enhance this shot to make anything out. You can see the VBlok all over, all the panels and floor were red. The Rockford Fosgate 600a5 amp is mounted in the middle and resides under the back seats with the Cap between the subs. I used Stinger Pro 12 gauge speaker wire, 4 gauge Custom Pro power and ground, Hyper series interconnects (4 2), 1/2 farad capacitor, and a lot of Stinger barrier spade, wire and grounding terminals.
Rockford Fosgate Punch 600a5
RMS Power (4 ohms) 50W x 4 100W x 1
RMS Power (2 ohms) 100W x 4 200W x 1
RMS Power (Bridged/Mono) 200W x 2 N/A
THD Distortion 100dB
Input Sensitivity 250mV-4V (low level) / 650mV-11V (high level)
Punch Bass Variable 0dB to 18dB @ 45Hz
Crossover Frequency 50Hz-210Hz LP/Full/HP
Crossover Slope 12dB/octave Butterworth
Height 2.62" (6.65cm)
Width 9.60" (24.38cm)
Length 18.27" (46.40cm)
Stinger Stiffening Capacitor
1/2 Farad Storage
20 Volt, 24 Volt Surge
Ultra Low ESRTemperature Range From -40C to 95C
GIVE ME THE BASS!... Show Less