Sign My Guestbook
25 comments
Posted by JdmBptAz
01/03/2007, 06:00pm
I havent done any upgrades yet it is still stock power, however i have a high flow ct26 turbo off an mr2 which i intend to add oneday soon.
Posted by haro5678
07/25/2006, 02:23pm
actually my car is a dx with a si engine, which i dont think u guys have, but pretty much its only got 125hp stock and it does have v-tec but the compression ratio is still low enough that i should be able to run 9-10 pounds of boost with out any worries.
Posted by haro5678
07/24/2006, 08:43am
very nice mx3 i liked that u went away from the usual 2.5 swap and did the 1.8 turbo. stop by and check out my work in progress sumtime
Posted by DAR_98GSR
07/11/2006, 03:55am
Il give ye a shot a my car tonight and see what the steerings like. and that nite I had clancy in my car aswell and the steering was fucked and with the bigger wheels etc.
Posted by DAR_98GSR
07/11/2006, 03:36am
wait til i get my steering rack sorted then il beat ye, i just cant race on corners at all now. and iv 17" wheels on compared to your 15"s. we'l know whos is quicker when we both have our exhausts and intercoolers on and you get your new wheels and id stil inihalate ye off the mark !! no doubt about that
Posted by DAR_98GSR
07/11/2006, 03:20am
Look at any gsr standard spec ye mad thing. They start at 200bhp!
Posted by DAR_98GSR
07/11/2006, 03:00am
I have only made it fit the bumbper and all, its not bolted in or nothin yet. It fits grand thou, it will look alot better when i get a smaller reg done up aswell.
Posted by HondaWonderBoy
07/06/2006, 08:53am
very nice MX-3. Turbo is certainly the way to go. g'luck with everything! Check out my turbo Accord!
Posted by Kubis
06/29/2006, 01:28pm
Yes, that are them.. what is your opinion?Better or worse than old 17".. ?
Posted by Kubis
06/15/2006, 12:08pm
The rims are on.. they fit great I think.. thanks for reply Kubis
Posted by Kubis
06/08/2006, 09:56am
Hi, my new rims arriverd (18") and I would need to know specs of that mazda rims (18") you had on yours just those you were trying and rubbered the front. I have R18 7/5 with ET42 (offset).. just have no time to try them on since my exams end. Please let me know yours offset number(ET) and if they were 7 or 7/5 wide.. so I can compare if mine will fit fine.. Thanx K.
Posted by Kubis
05/31/2006, 12:25am
Hi,
so how it looks with the BP-T?I think to do the same. It is possible to buy this engine for 1500Eur + shipping, what was your price, is the swap done already?Add pics when done.. cheers Kubis
so how it looks with the BP-T?I think to do the same. It is possible to buy this engine for 1500Eur + shipping, what was your price, is the swap done already?Add pics when done.. cheers Kubis
Posted by BJB-SW
04/29/2006, 06:51am
nice mx 3! a rare car sighting in our country.. i bet with a new paint job, it'l look like an ass whipper! nice! visit my site too, and keep the mods coming!
Posted by marlonthegreat
04/14/2006, 02:25am
Thanks for viewing my site. Regarding your query, there is no way you can fit the 1.8 clutch disc and plate in your 1.5 tranny. what i did was to look for a 1.8 naturally aspirated motor with a front wheel drive transmission. As you've noticed the gtx motor (BPT) is 4wd, so you can't use its transmission with your mx-3. However, you can use the 1.8 (engine code BP) front wheel drive N/A tranny. It will easily BOLT ON the gtx motor. I also used the axels of the 1.8 N/A tranny since they are bigger in diameter, hence stronger than the 1.5 or 1.6 axels. The advantages of using the 1.8 N/A transmission is that it can house the 1.8 gtx clutch disk and plate including the flywheel which are bigger than the 1.5 disk, plate and flywheel. hence more clamping power.
Posted by Eskimo_MX3
04/05/2006, 01:23pm
I like it. You should check out mine. I'm thinking what engine to swap for when I get the money. Mine's stock 'cept the paint right now.
Posted by Kubis
03/16/2006, 08:22am
Hi again.. This is final price with all charges what I have to pay (except the 17euro for delivery in CZECH REPUBLIC). We are also in EU so it might not be problem to get these rims for you without paying any charges except the cost for transport to Ireland. But I think PPL or UPS does it for good. I have already heard about Autozam so thats why there is the different engine. How much horsepower does it have? I need more than 107Hp for my car so some swap would be a solution. Let me know how the work goes.. Im excited about this project.. see the rims variations on. http://www.sportovniautodoplnky.cz/store/default.asp?lngDepartmentID=1
Kubis
Kubis
Posted by Kubis
03/15/2006, 12:33pm
Hi.. the price for my rims 18" with rubber 215/35 is 983EURO.As I was surprised with beeing your car 1.5.. I didnt know they put in MX this motor.. I know about 1.6 SOHC/DOHC ..V6 1.8 ..V6 2.5 KLZE but never heard about 1.5. And from which car is that 1.8 turbo engine? The 17" I have sold aro on all pix on the car.. the 18´s are the pix on first site, just the rim. Chers to Ireland..
Kubis
Kubis
Posted by Kubis
03/10/2006, 12:51pm
Cheers, nice wheels, nice lowering job.. I like your car except the wing. Im not fan of wigs. But yes yours is simple.. and seems best of those possible on MX. I ordered 18s from US to europe.. so let me know if you like them..
Kubis
Is that really 1.5???
Kubis
Is that really 1.5???
25 comments
